BIOGRASS EXTRA®
TECHNICAL PRODUCT BULLETIN #SW-46
USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION
ORIGINAL LISTING DATE: AUGUST 17, 2010
“BIOGRASS EXTRA®”
| I. NAME, BRAND, OR TRADEMARK |
|---|
| BIOGRASS EXTRA® Type of Product: Surface Washing Agent |
| II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT |
|---|
| Química del Desierto, S. de R.L. de C.V. Madrid 2001-A Col. Mirador Chihuahua City, Chihuahua, Mexico C.P. 31205 Phone: +52-1-614-110-2650 E-mail: erich.wolf@biograssextra.com Web site: https://biograssextra.com/ (Ing. Erich Wolf) |
| III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS |
|---|
| HRD Ecological Equations LLC 1417 Palma Plaza Austin, Texas, 78703 Phone: (512) 789-4881 E-mail: info@biograssextra.com (Mr. Howard Reed) |
| IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION |
|---|
| 1. Flammability: Non-flammable (DOT: Non-hazardous). 2. Ventilation: No special requirements. 3. Skin and eye contact; protective clothing; treatment in case of contact: No special equipment or clothing required, however goggles are recommended. In case of eye irritation, flush with plenty of fresh water. 4.a. Maximum storage temperature: 120°F continuous, 140°F up to 5 days 4.b. Minimum storage temperature: 35°F 4.c. Optimum storage temperature range: 40°F to 120°F 4.d. Temperatures of phase separations and chemical changes: Mix well before use if outside the 60-85°F range. |
| V. SHELF LIFE |
|---|
| Two years minimum. |
| VI. RECOMMENDED APPLICATION PROCEDURE |
|---|
| Recommended application procedures depending on concentration of contaminants, water salinity levels, water temperature, and the type and age of the contaminant. There are two means of application: power spraying or direct application. a. Application via power spraying: Use of a power washer to spray the contaminated surface. The action may be improved by warming the product during use. b. Application via direct application: Remove contaminated soil, sand, etc. into a container. Irrigate the affected ground with the product and let it soak in. Agitate the mixture of water/product/ground and add additional water to float the contaminant off of the surface. A layer of product-contaminant will form which may be physically separated from the soil. The oil in this layer may be separated by dehydration or pumping to prepare the contaminant for disposal or reclamation. The clean soil or sand may be returned to its original environment. The residue should be removed and disposed of as required by local, state, or federal regulations. The on-site coordinator can determine the best way to recover the residue based on the spill type, surface, and environment of the area. Concentrations: The concentration of the BIOGRASS EXTRA® product to be used depends on the density of the contaminant. Normally the product is used in a one-to-one proportion with the contaminant. |
| VII. TOXICITY AND EFFECTIVENESS | |||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
a. Toxicity:
b. Effectiveness NA |
| VIII. MICROBIOLOGICAL ANALYSIS |
|---|
| NA |
| IX. PHYSICAL PROPERTIES |
|---|
| 1. Flash Point: >93°C 2. Pour Point: 21.0°F 3. Viscosity: 1.37 cst @40°C 4. Specific Gravity: 1.0253 @60°F 5. pH: 7.1 6. Surface Active Agents: Anionic and nonionic, proprietary, surfactants 7. Solvents: Water 8. Additives: Sodium phosphate dibasic, sodium chloride 9. Solubility: Miscible in water and some solvents |
| X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS | ||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
|